Texas Instruments TPS62840DLCR: PCB footprint and gate checks

The Texas Instruments TPS62840DLCR is a 750 mA ultra-low-IQ synchronous buck from Texas Instruments. Its package or board interface is 8-pin 2 × 3 mm VSON-HR, and its relevant electrical envelope is 1.8–6.5 V input, selectable/fixed output options, 750 mA, roughly 60 nA IQ. It communicates or connects through synchronous buck with VSEL/MODE controls. Those fields belong together: substituting a familiar family name while changing package, voltage, sensing port, mount style, current class, or interface behavior can leave a PCB that passes ordinary net checks and still cannot be assembled or function safely.

TPS62840 combines sub-microamp standby with useful burst current, making leakage and light-load mode central to the design.

Common uses include coin-cell and primary-battery sensors and always-on low-power 3.3/1.8 V rails. Start with the manufacturer drawing and recommended application, then record the exact ordering suffix alongside the KiCad symbol and footprint. This makes the library evidence reviewable when the part is re-sourced months later.

• Use the exact IC land pattern and exposed-pad/via guidance. Place the input capacitor, high-side switch pins, diode where asynchronous, inductor, and output capacitor to minimize the hot-loop area.
• Keep the SW node compact and free of test points or broad copper that becomes an antenna. Route feedback from the quiet output after the inductor and away from SW, gate-drive, and inductor fields.

Keep the tiny power loop compact, set VSEL/MODE deliberately, and audit every divider, pull-up, capacitor leakage, and load path that can dominate nanamp regulator current.

• Select inductor saturation/current rating, switching frequency, compensation or feed-forward parts, input/output capacitors, and divider values from the manufacturer's equations and reference layout for the real voltage/current case.
• Check startup, enable, soft start, light-load mode, minimum on-time, duty cycle, and thermal behavior across input range. A copied module schematic is not enough when the PCB geometry controls stability and EMI.

Put the support components where their current, thermal, optical, RF, or measurement loops are actually short—not merely where ratsnest lines look tidy. Confirm pin one from the package view used in the datasheet, distinguish top view from mating face or bottom view, and check mask, paste, drill, courtyard, enclosure, and rework access independently. A correct copper pad pattern can still be a bad production footprint when the sensing opening, connector latch, exposed pad, thermal path, or cable volume is wrong.

MakeIRL’s release gate should not stop at “the symbol has the right number of pins.” For this part, a useful gate review combines ERC/DRC with the following package- and function-specific evidence:

1. Check package pinout, exposed pad, hot-loop placement, switch-node size, inductor value and saturation, diode orientation where used, divider, compensation, and capacitor ratings.
2. Check input/output polarity, feedback Kelvin route, ground partition and stitching, current capacity, thermal vias, and clearance from RF/analog circuits.
3. Check exact IC suffix and switching frequency plus lifecycle; marketplace modules may not contain the IC advertised in their title.
4. For Texas Instruments TPS62840DLCR, check DLC footprint, voltage-option/VSEL state, MODE, 6.5 V max, inductor, capacitors, light-load ripple, leakage, and 750 mA peak.

Then run ERC and DRC, refill zones, and inspect the fabrication and assembly outputs. Cross-probe the exact pads named by any finding, compare the BOM MPN with the footprint and electrical limits above, and verify that a real cable, enclosure, antenna, sensor stimulus, load, or thermal path can be tested on the assembled unit. An exclusion is evidence that someone dismissed a marker; it is not evidence that the underlying condition was resolved.

The most expensive errors are usually plausible: a footprint from a sibling package, a breakout-board voltage copied to the bare IC, a headline current used without thermal analysis, or a connector family selected by pitch alone. For Texas Instruments TPS62840DLCR, review these failure modes explicitly:

• Selecting high-leakage electrolytics or indicator dividers can erase the energy benefit of a 60 nA converter.
• Routing feedback under the inductor or beside SW, producing load-dependent ripple, jitter, or outright instability.
• Choosing an inductor by nominal current while ignoring saturation current and loss at the regulator's switching frequency.

Sourcing note. Use TPS62840DLCR's exact option code and TI source; verify output selection and package against the BOM, not family shorthand. The approved vendor list should preserve manufacturer, full suffix, package, voltage/range/accuracy grade, lifecycle, and mating or external components. An alternate is real only after its datasheet, land pattern, electrical behavior, firmware assumptions, and assembly process have all been compared—not because a distributor search places it in the same parametric row.