Bosch BMP390 PCB footprint, checks, and sourcing guide

The Bosch BMP390 is a high-accuracy barometric pressure sensor from Bosch Sensortec. Its package or board interface is 10-pin 2.0 × 2.0 mm LGA with top port, and its relevant electrical envelope is 1.65–3.6 V VDD and 1.2–3.6 V VDDIO. It communicates or connects through I²C or SPI; 0x76/0x77. Those fields belong together: substituting a familiar family name while changing package, voltage, sensing port, mount style, current class, or interface behavior can leave a PCB that passes ordinary net checks and still cannot be assembled or function safely.

BMP390 offers lower noise and higher relative accuracy than BMP280 in a smaller 10-pin package with a different footprint and filtering behavior.

Common uses include precision altimeters and wearable elevation tracking. Start with the manufacturer drawing and recommended application, then record the exact ordering suffix alongside the KiCad symbol and footprint. This makes the library evidence reviewable when the part is re-sourced months later.

• Use the sensor maker's land pattern and paste guidance for the exact LGA/DFN package. Keep copper, solder mask, and cleaning residue away from any pressure, humidity, or thermal opening called out in the package drawing.
• Give the package a courtyard that protects its sensing port and allows rework. Do not place a via, glue dot, conformal coating, or enclosure rib over the opening.

Mechanically isolate it from board flex and rapid airflow, vent the enclosure, and use oversampling/IIR settings appropriate to motion versus response time.

• Place the sensor away from regulators, processors, batteries, displays, and board-edge drafts unless those are the intended measurement. Use a thermal neck or isolated board region when ambient temperature accuracy matters.
• Decouple at the supply pin, keep digital pull-ups within the allowed I/O voltage, and follow the datasheet's startup, heater, and measurement timing. Vent the enclosure so the sensor sees the medium without admitting liquid water or assembly contamination.

Put the support components where their current, thermal, optical, RF, or measurement loops are actually short—not merely where ratsnest lines look tidy. Confirm pin one from the package view used in the datasheet, distinguish top view from mating face or bottom view, and check mask, paste, drill, courtyard, enclosure, and rework access independently. A correct copper pad pattern can still be a bad production footprint when the sensing opening, connector latch, exposed pad, thermal path, or cable volume is wrong.

MakeIRL’s release gate should not stop at “the symbol has the right number of pins.” For this part, a useful gate review combines ERC/DRC with the following package- and function-specific evidence:

1. Check package orientation, exposed-port keepout, supply and I/O ranges, local decoupling, I²C/SPI address straps, pull-up rail, and any mandatory no-connect pads.
2. Check that heat sources, copper pours, airflow, coating, adhesive, and enclosure features do not bias or block the measurement.
3. Check the exact orderable suffix, accuracy grade, package, address, and lifecycle rather than treating a breakout-board name as the component MPN.
4. For Bosch BMP390, check the 10-pin BMP390 footprint, VDD/VDDIO, CSB/SDO, interrupt, top port, enclosure vent, and pressure-range assumptions.

Then run ERC and DRC, refill zones, and inspect the fabrication and assembly outputs. Cross-probe the exact pads named by any finding, compare the BOM MPN with the footprint and electrical limits above, and verify that a real cable, enclosure, antenna, sensor stimulus, load, or thermal path can be tested on the assembled unit. An exclusion is evidence that someone dismissed a marker; it is not evidence that the underlying condition was resolved.

The most expensive errors are usually plausible: a footprint from a sibling package, a breakout-board voltage copied to the bare IC, a headline current used without thermal analysis, or a connector family selected by pitch alone. For Bosch BMP390, review these failure modes explicitly:

• Dropping BMP390 onto a BMP280/BME280 footprint because all are Bosch barometers will misalign the package and pads.
• Placing the sensor beside an LDO or radio and calibrating out a self-heating error that changes with workload and battery voltage.
• Washing or conformally coating a humidity or pressure port, permanently changing response or blocking it.

Sourcing note. Use the exact BMP390 order code and review Bosch's newer BMP390L/BMP5xx options if lifecycle is critical. The approved vendor list should preserve manufacturer, full suffix, package, voltage/range/accuracy grade, lifecycle, and mating or external components. An alternate is real only after its datasheet, land pattern, electrical behavior, firmware assumptions, and assembly process have all been compared—not because a distributor search places it in the same parametric row.